Author Topic: (HeightMap) Engraving a Bitmap or Jpeg  (Read 12587 times)

Offline 4M Tool

  • Ewok
  • *
  • Posts: 12
  • I try to put forth a effort
    • View Profile
(HeightMap) Engraving a Bitmap or Jpeg
« on: November 21, 2008, 18:28:37 pm »
Made a clip of how I make a Heightmap with CamBam free.Iam new to CamBam so if its not completly wright,O well,it works. :)And iam sure the helpful peps here will correct newbie probs. :)

http://www.youtube.com/watch?v=A3lBZo--kfU
 

Offline mrbean

  • Administrator
  • Storm Trooper
  • *****
  • Posts: 213
  • Web Jedi
    • View Profile
    • MrBean's CNC Projects
Re: (HeightMap) Engraving a Bitmap or Jpeg
« Reply #1 on: November 21, 2008, 20:42:51 pm »
Nice.  I think that might be the first CamBam video tutorial.
Good job.

Offline 10bulls

  • Administrator
  • CNC Jedi
  • *****
  • Posts: 2163
  • Coding Jedi
    • View Profile
    • www.cambam.info
Re: (HeightMap) Engraving a Bitmap or Jpeg
« Reply #2 on: November 23, 2008, 09:43:49 am »
Thank you so much for doing that.  Video tutorials are something that have been on my todo list for a long time, hopefully this will inspire me to crack on with some of my own.
What capture program do you use?  I've had a brief look at Camtasia and CamStudio ... both looked good but I liked the price of CamStudio better! ;)

A test to try to link to your video in a forum post....
<a href="http://www.youtube.com/v/A3lBZo--kfU&amp;hl=en&amp;fs=1" target="_blank" rel="noopener noreferrer" class="bbc_link bbc_flash_disabled new_win">http://www.youtube.com/v/A3lBZo--kfU&amp;hl=en&amp;fs=1</a>

The content of the video looked fine and was well explained.

The heightmap plugin hasn't changed much since I first knocked it together, very early in CamBam's development so there are a few fixes and improvements needed as you no doubt discovered.


Offline 4M Tool

  • Ewok
  • *
  • Posts: 12
  • I try to put forth a effort
    • View Profile
Re: (HeightMap) Engraving a Bitmap or Jpeg
« Reply #3 on: November 24, 2008, 12:13:47 pm »
Iam using Cam Studio.Need a better mic to pic up my "muffled" mouth.Not that i know anything about whats a good capture program,but like you said the price of CamStudio is nice. :)
Just like the price of the CamBam. ;)
Thanks again,
Troy
« Last Edit: November 24, 2008, 12:15:36 pm by 4M Tool »

Offline 4M Tool

  • Ewok
  • *
  • Posts: 12
  • I try to put forth a effort
    • View Profile
Re: (HeightMap) Engraving a Bitmap or Jpeg
« Reply #4 on: November 25, 2008, 12:55:47 pm »
Hello,
 Made another HeightMap clip,that i beleive is better to shew CamBam :)
Troy

http://www.youtube.com/watch?v=kIO-ZxW8PHM
« Last Edit: November 25, 2008, 13:15:30 pm by 4M Tool »

Offline rog8811

  • Ewok
  • *
  • Posts: 3
    • View Profile
Re: (HeightMap) Engraving a Bitmap or Jpeg
« Reply #5 on: February 13, 2009, 17:57:29 pm »
Hi folks, as I cannot find an "introduce yourself" section so I will post my first one here  :)

I found and downloaded CamBam today and actually produced some code thanks to the above videos, thankyou for posting them!


Regards rog8811
« Last Edit: February 13, 2009, 21:55:26 pm by rog8811 »
In the land of the blind the one eyed man.....
is, most likely, holding the laser.

Offline 10bulls

  • Administrator
  • CNC Jedi
  • *****
  • Posts: 2163
  • Coding Jedi
    • View Profile
    • www.cambam.info
Re: (HeightMap) Engraving a Bitmap or Jpeg
« Reply #6 on: February 15, 2009, 00:02:30 am »
Hello and welcome to the forum.

Yes, I too am very grateful for these excellent videos - thank you very much Troy.